Micro Maxx Model Rocket Engines (6 Pack)
6 Pack, 6mm diameter
Micro Sonda II B Model Rocket Kit
The Sonda II B is the largest of Brazil's series of Sonda II sounding rockets. The Sonda II was first flown during the early 1970's and continues in use today.
This Micro kit is designed to use the Quest™ Micro Maxx™ engines and is based on our "Minimum Diameter" T-MM body tubes. Includes 3D printed nose cone, Kevlar® shock cord, metallized polyester streamer, water-slide decal and our usual complete instructions. Due to the small parts involved, these kits are not recommended for the first-time modeler. Younger modelers should have the assistance of an adult when trying to construct these small kits.
Specifications:
Length: 5.38"/136.5 mm
Diameter: 0.282"/7.16 mm
Approx. Weight: 0.11 oz/3 gm
Skill Level: Intermediate
Scale: 1/41.5 (0.024)
Recovery Device: Streamer
Recommended Engines: Quest™ Micro Maxx™
What you'll need to build this model:
Adhesives (a quick-curing epoxy glue can be used for most steps and is recommended, cyanoacrylate [“CA”] is recommended for some steps and you may also use throughout if preferred); hobby knife with a sharp #11 blade; straight edge (preferably metal); double-sided cellophane ("Scotch") tape; paint (Spray or bottle paint, such as such as Rust-Oleum, Krylon, or Testors is recommended. Be sure not to mix different types or brands of paint without testing.) - primer (optional), white, fluorescent red & clear (optional); sandpaper (medium - 220 or 280, fine - 320 or 400, & [optionally] extra fine - 500 or 600); pencil.
Recommended, but not required: tweezers (or needle nose pliers); sanding block; tack cloth; decal setting solution such as Micro Set or Micro Sol.
What else you'll need to fly this model:
Electronic launch system; launch pad with Micro Maxx™ size launch rod; recovery wadding; Micro Maxx™ engines.
This Micro kit is designed to use the Quest™ Micro Maxx™ engines and is based on our "Minimum Diameter" T-MM body tubes. Includes 3D printed nose cone, Kevlar® shock cord, metallized polyester streamer, water-slide decal and our usual complete instructions. Due to the small parts involved, these kits are not recommended for the first-time modeler. Younger modelers should have the assistance of an adult when trying to construct these small kits.
Specifications:
Length: 5.38"/136.5 mm
Diameter: 0.282"/7.16 mm
Approx. Weight: 0.11 oz/3 gm
Skill Level: Intermediate
Scale: 1/41.5 (0.024)
Recovery Device: Streamer
Recommended Engines: Quest™ Micro Maxx™
What you'll need to build this model:
Adhesives (a quick-curing epoxy glue can be used for most steps and is recommended, cyanoacrylate [“CA”] is recommended for some steps and you may also use throughout if preferred); hobby knife with a sharp #11 blade; straight edge (preferably metal); double-sided cellophane ("Scotch") tape; paint (Spray or bottle paint, such as such as Rust-Oleum, Krylon, or Testors is recommended. Be sure not to mix different types or brands of paint without testing.) - primer (optional), white, fluorescent red & clear (optional); sandpaper (medium - 220 or 280, fine - 320 or 400, & [optionally] extra fine - 500 or 600); pencil.
Recommended, but not required: tweezers (or needle nose pliers); sanding block; tack cloth; decal setting solution such as Micro Set or Micro Sol.
What else you'll need to fly this model:
Electronic launch system; launch pad with Micro Maxx™ size launch rod; recovery wadding; Micro Maxx™ engines.
Related Items
Complete Micro Maxx Launch System (Quest)
Electronic Launch System with Launch Pad for Micro Maxx